Perahome

Product Code: EZ Features: Economically priced, Excellent Hiding Power, Matt Finish Pera CEILING PAINT is a water based emulsion paint for interior and exterior use on plaster, concrete, fibre cement and Cellotex with a high hiding power. This product was especially developed for housing schemes, factories ect., where White colour high hiding is important.  PROPERTIES DATA UNITS Resin Type Acrylic - Drying Times - Touch Dry 20 minutes Drying Times - Hard Dry 2 hours Over coating Time 6 hours Recommended number of coats 2 - Coverage +/- 7 m² / Ltr Surface Apperance Matt - Cleaning Solvent Water - Shelf Life 6 months Available Colours Whilte, Other Colours available on request - Unit Sizes and Weights 20Ltr = 32.6kg, 5Ltr = 7.7kg, 1Ltr = 1.6kg Ltr = kg SUBSTRATE SEALER / FIRST COATER UNDERCOAT / FIRST COATER Mineral or Fiber Cement Substrate - New One coat Pera Aquaprime N/A Mineral or Fiber Cement Substrate - Previously Coated * Prepare as below N/A Cellotex - New N/A N/A Cellotex - Previously Coated ** Prepare as below N/A Previously coated*mineral surface or fiber cement : Poor condition: Remove existing paint completely. Make sure plaster or concrete surface is in good condition. Continue as for new mineral substrate or Fiber Cement substrate. Good condition - ensure surface is clean and dry, glossy surfaces have to be sanded down. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with Pera Mastix (interior) or Pera Crackfiller (exterior). After drying seal Pera Crackfiller with Pera Seal. Previously coated** Cellotex: Remove poorly adhering paint and sand down glossy surfaces. Make sure surface is clean and dry. Apply 2 coats Pera CEILING PAINT with a sheepskin roller. NB: Always use a sealer and / or primer, before applying Pera Ceiling Paint. For sealer and filler application instructions, see relevant data sheets. Remember - a system is only as good as the substrate. For application surfaces, other than above, please contact our sales department. Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water. Ventilation Ensure adequate ventilated application area. Spillages Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact.  ...

Product Code: DC Features: Water-based, pure acrylic roof paint. Ready to use. Self-priming. Heat Reflective. Pera Coolroof is a water-based – self priming – pure Acrylic roof paint, based on special ceramic fillers and pigments to reflect UV-light rays and to interrupt the conductive heat transfer to the substrate. However, maximum heat reflection will be achieved by using white or pastel shades Pera Coolroof. The heat isolating properties of Pera Coolroof are proportional to the applied dry film thickness.  Description, Properties and Uses: The development of PERA COOLROOF was based on our - over 2 decades successfully performing – PeraRoof. By using latest technologies and high performance raw materials, obvious improvements in a number of aspects have been achieved: No bleeding or washing off during rainfalls Colour retention, as only lightfast pigments are used (no chalking or fading) Further increased cooling effect Corrosion protection – self-priming (not in coastal areas) Improved adhesion and over coating. PROPERTIES DATA UNITS Resin Type Pure Acrylic - Drying Times - Touch Dry 30 minutes Drying Times - Hard Dry 2 hours Over coating Time 6 hours Recommended number of coats 2 to 3 - Coverage 4 to 5 m² / Ltr Surface Apperance Matt, Mineral Look - Cleaning Solvent Water - Shelf Life 6 months Available Colours See colour card and White other pastel and deep colours on request - Unit Sizes and Weights 20Ltr =22kg, 5Ltr = 5.6kg, 1Ltr = 1.2kg Ltr = kg Always make sure surface is clean and dry before any sealer or primer is applied. SUBSTRATE CLEANER PRIMER, SEALER Galvanized Iron - New Pera Metal Cleaner N/A (Self-priming) Mineral Substrate - Previously Coated * Prepare as below Prepare as below Previously coated* surface in good condition: Sand down glossy surfaces. Touch up holes with Pera Antirust primer. Make sure surface is clean and dry. Previously coated* surface in poor (paint peeling and extreme chalking) condition: Remove existing paint. New galvanized iron: Apply 2 to 3 coats Pera Coolroof directly onto degreased and cleaned surface.   Previously coated mineral substrate: On previously coated, prepared surfaces, 2 coats of Pera Coolroof should be applied.   New fiber cement: Make sure fiber cement is free from dust & other contaminations by means of stiff brush – if necessary wash with clean water & let dry properly. Apply one coat Pera Coolroof thinned with to 15% water, leave to dry and apply two coats un-thinned. NB: Do not paint a roof in full sun (hot substrate) or very windy conditions. Make sure that the coating is dry, before it rains. Stir well before and during use. The optimal cooling properties of Pera Coolroof are only achieved with a white or pastel colour. For application surfaces, other than above, please contact our sales department. Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water. Ventilation Ensure adequate ventilated application area. Spillages Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact.  ...

Product Code: EH Features: Rustic Natural Look, Permeable, Long lasting, Flexible, Ultraviolet- and alkali resistance, Environmental & user friendly PERA FINE TEX  is a Pure Acrylic wall coating, with a mini texture. To be used direct on plaster PROPERTIES DATA UNITS Resin Type Acrylic - Drying Times - Touch Dry 30 minutes Drying Times - Hard Dry 2 hours Over coating Time 4 hours Recommended number of coats 1 Prime-Coat and 1 to 2 topcoats - Coverage 5 to 6 m² / Ltr Surface Apperance Fine Texture - Matt - Cleaning Solvent Water - Shelf Life 6 months Available Colours See colour card, other colours on request - Unit Sizes and Weights 20Ltr = 30.1kg, 5Ltr = 7.6kg, 1Ltr = 1.5kg Ltr = kg SUBSTRATE PRIMER SEALER, UNDERCOAT Mineral Substrate - New 1 Coat MB-20 N/A Mineral Substrate - Previously Coated * Prepare as below N/A Previously coated* surface in good condition: Sand down glossy surfaces. Touch up holes and cracks with Flexfill (XRP-2) or PeraCrackfiller (MXF-2) (Seal Pera Crackfiller. with Pera Seal (B-30)). Make sure surface is clean and dry. Previously coated* surface in poor condition: Remove existing paint. Ensure substrate is completely dry and clean. Apply one coat Anti Salt Primer (MB-20). Leave to dry for 2 days Apply with 2 coats Pera Fine Tex with a lambwool roller and if desired, immediately drag with block brush for pattern. NB: Due to the surface texture of Pera Fine Tex, touch-up areas will appear different in colour. It is therefore advisable to paint the surface from joint to joint or corner to corner. For application surfaces, other than above, please contact our sales department (Tel: (061) 22 7050) or the technical department (Tel: (061) 22 7773) Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water! Ventilation Ensure adequate ventilated application area! Spillages Soak up with sand or soil. Prevent run off into drains or waterways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact. Keep away from open flames. ...

Product Code: FS Features: Ready to use, Flexible PERA FLOOR PAINT is a quality, high build floor coating for use on interior and exterior concrete floors, with exceptional abrasion resistance. It should not be used on floors, which come in contact with breakfluid, solvents, oils, ect. Application by brush or roller Easy application (PVA like). Dries to a tough finish Can be applied direct to plaster, concrete and fibre cement substrate (self-priming) PROPERTIES DATA UNITS Resin Type Acrylic - Drying Times - Touch Dry 30 minutes Drying Times - Hard Dry 2 hours Over coating Time 4 hours Recommended number of coats 1 Prime Coat / 2 Top Coats - Coverage +/- 5 m² / Ltr Surface Apperance Matt Finish - Cleaning Solvent Water - Shelf Life 6 months Available Colours See colour card - Unit Sizes and Weights 20Ltr = 28.5kg, 5Ltr = 7,2kg Ltr = kg SUBSTRATE PRIMER, SEALER UNDERCOAT, FIRST COATER Mineral Substrate - New Self Priming N/A Mineral Substrate - Previously Coated * Prepare as below N/A Previously coated* surface painted with PVA, in good condition: Sand down glossy surfaces. Repair plaster where necessary. Make sure surface is clean and dry. Previously coated* surface in poor condition: Remove existing paint. New mineral substrate: For a long-term coating, apply 2 to 3 coats Pera Floor Paint directly onto mineral surface. First coat must be diluted with 10% water, consecutive coats to be applied undiluted.   Previously coated with PVA paint: On previously coated, prepared surfaces, 2 coats of Pera Foor Paint should be applied.  NB: Pera Floor Paint should not be applied on Epoxy Paints. For application surfaces, other than above, please contact our sales department. Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water. Ventilation Ensure adequate ventilated application area. Spillages Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact.  ...

Product Code: XRP-2 Features: High Flexibility, Good Adhesion, Quick sandable. PERA MASTIX is a highly flexible compound for use as crack filler for interior and exterior masonry and metal surfaces. PROPERTIES DATA UNITS Resin Type Acrylic - Drying Times - Touch Dry Depends on thickness minutes Drying Times - Hard Dry Depends on thickness hours Over coating Time 2 Depending on thickness hours Recommended number of coats N/A - Coverage N/A m² / Ltr Surface Apperance Smooth - Cleaning Solvent Water - Shelf Life 6 months Available Colours Whilte - Unit Sizes and Weights 5Ltr = 5.5kg, 1 Ltr = 1.1kg Ltr = kg Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water. Ventilation Ensure adequate ventilated application area. Spillages Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact.  ...

Product Code: EO Features: Economically priced, Good Hiding Power, Cleanable, Matt Finish PERA MATT PVA is a water based emulsion paint for interior and exterior use on plaster, concrete, fibre cement and Cellotex with good durability. Improved formula for mixing in pastel and deep colours with better dry hiding. PROPERTIES DATA UNITS Resin Type Acrylic - Drying Times - Touch Dry 20 minutes Drying Times - Hard Dry 2 hours Over coating Time 6 hours Recommended number of coats 2 - Coverage +/- 7 m² / Ltr Surface Apperance Matt - Cleaning Solvent Water - Shelf Life 6 months Available Colours Whilte, Other Colours available on request. This quality is only made in pastel and deep shaded - Unit Sizes and Weights 20Ltr = 32.6kg, 5Ltr = 7.7kg, 1Ltr = 1.6kg Ltr = kg SUBSTRATE SEALER / FIRST COAT UNDERCOAT / FIRST COATER Mineral or Fiber Cement Substrate - New One coat Pera Aquaprime N/A Mineral or Fiber Cement Substrate - Previously Coated * Prepare as below N/A Cellotex - New One coat Pera Seal N/A Cellotex - Previously Coated *** Prepare as below N/A Previously coated*mineral surface or fiber cement : Poor condition: Remove existing paint completely. Make sure plaster or concrete surface is in good condition. Continue as for new mineral substrate or Fiber Cement substrate. Good condition: Ensure surface is clean and dry, glossy surfaces have to be sanded down. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with Pera Mastix (interior) or Pera Crackfiller (exterior). After drying seal Pera Crackfiller with Pera Seal. Previously coated** Cellotex: Remove poorly adhering paint and sand down glossy surfaces. Make sure surface is clean and dry. Apply 2 coats PERA MATT PVA with a sheepskin roller. NB: Always use a sealer and / or primer, before applying Pera Matt PVA. For sealer and filler application instructions, see relevant data sheets. Remember - a system is only as good as the substrate. For application surfaces, other than above, please contact our sales department. Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water. Ventilation Ensure adequate ventilated application area. Spillages Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact.  ...

Product Code: ER Features: Silicon resin PVA, Good colour retention, Matt mineral finish (micro texture), Clean brilliant colour development Description, Properties and Uses: Water-vapour permeability Water repellency Colour fading (for optimal exterior performance we offer lightfast pigments) Chalking- and UV-resistance Resistance to saponification PERA MICRO TEX, offers the solution to all the above mentioned critical aspects. It is recommended for interior and exterior use on primed plaster-, concrete- and fibre cement substrates, offering a hardwearing and good cleanable exclusive finish with very high water-vapour permeability together with excellent water repellency and extreme durability. PROPERTIES DATA UNITS Resin Type Silicone modified Acrylic Emulsion - Drying Times - Touch Dry 30 minutes Drying Times - Hard Dry 2 hours Over coating Time 6 hours Recommended number of coats 1 prime-coat / 2 Top Coats - Coverage 6 to 7 m² / Ltr Surface Apperance Matt Mineral Finish - Cleaning Solvent Water - Shelf Life 6 months Available Colours See colour card and White, Other Colours on Request - Unit Sizes and Weights 20Ltr = 28.2kg, 5Ltr = 7, 1 Ltr = 1.4kg Ltr = kg SUBSTRATE PRIMER / SEALER UNDERCOAT, FIRST COATER Mineral Substrate - New 1 coat MB-20 N/A Mineral Substrate - Previously coated * n.a.  N/A Previously coated – paint surface in good condition Sand down glossy surfaces. Touch up holes and cracks with Flexfill (XRP-2) or PeraCrackfiller.(MXF-2) (PeraCrackfiller must be sealed with PeraSeal (B-30).) Make sure surface is clean and dry. New concrete walls: Ensure substrate is completely dry and clean. Apply one coat Anti Salt Primer (MB-20). Leave to dry for 2 days. Apply 2 coats Pera Micro Tex.   Previously painted concrete walls: Existing surface in poor condition - remove existing paint completely, and continue as in 1. Existing surface in good condition – On previously coated, prepared surfaces, 2 coats of undiluted Pera Micro Tex should be applied. This coating system will not be “permeable” due to the previous coatings underneath the Pera Micro Tex.  NB: For application on surfaces, other than above, please contact our sales department (Tel: (061) 22 7050) or the technical department (Tel: (061) 22 7773). Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water! Ventilation Ensure adequate ventilated application area! Spillages Soak up with sand or soil. Prevent run off into drains or water ways! Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight. Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact. Keep away from open flames.  ...

Product Code: DRC Features: UV Stable, Very Good Adhesion, Highly Flexible PERA REPAIR COMPOUND is a highly flexible compound for use as joint and crackfiller, to seal roof leak and for flashing. PROPERTIES DATA UNITS Resin Type Acrylic - Drying Times - Touch Dry 20 minutes Drying Times - Hard Dry Depends on film thickness hours Over coating Time +/- 6 (depends on film thickness) hours Recommended number of coats 2 to 3 - Cleaning Solvent Water - Shelf Life 6 months Available Colours See colour card and White - Unit Sizes and Weights 5Ltr = 6.8kg, 1Ltr = 1.4kg Ltr = kg Joints and cracks: Surface must be clean and dry. Break open large cracks and remove all loose plaster. Soak work area with Pera Seal and allow to dry. Add Pera Marbel Dust Fine (MD200) +/- 10% to the Pera Repair Compound, to form a thick paste and apply 2 to 3 layers. Allow sufficient drying time between layers. Smooth surface while still wet, as it cannot be sanded when dry.   Sealing of roofs: Remove loose screws and narrow hole by inserting matchsticks or wood shavings. Dip screw into Pera Repair Compound and fasten firmly. Holes and gaps can be sealed by flashing. Do not try to seal corroded roofs, as this would only be a temporary solution. Flashing: Make sure surface is clean and dry. For plastered surfaces seal with Pera Seal. Apply a thin layer of Pera Repair Compound and cover with netting. Allow to dry and apply a second layer. Smooth surface while still wet, as it cannot be sanded when dry. NB: Pera Repair Compound may not be used to repair cracks in swimming pools or any other area, where it will be covered by water. Tools must be cleaned with water immediately after use. For Pera Seal and roof coatings see relevant datasheets. Remember a system is only as good as the substrate. For application surfaces, other than above, please contact our sales department. Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water. Ventilation Ensure adequate ventilated application area. Spillages Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact.  ...