Perabuild

Product Code: MEZ Features: Economically priced, excellent hiding power, matt finish CEILING PAINT is a water based emulsion paint for interior and exterior use on plaster, concrete, fibre cement and Cellotex with a high hiding power. This product was especially developed for housing schemes, factories ect., where White colour high hiding is important. PROPERTIES DATA UNITS Resin Type Acrylic - Drying Times - Touch Dry 20 minutes Drying Times - Hard Dry 2 hours Over coating Time 6 hours Recommended number of coats 2 - Coverage +/- 7 m² / Ltr Surface Apperance Matt - Cleaning Solvent Water - Shelf Life 6 months Available Colours White Only - Unit Sizes and Weights 20 Ltr = 32.6kg, 5 Ltr = 7.7kg, 1 Ltr = 1.6kg Ltr = kg SUBSTRATE SEALER / FIRST COATER UNDERCOAT, FIRST COATER Mineral or Fiber Cement Substrate - New One coat Plater Primer (MCE-1) N/A Mineral or Fiber Cement Substrate - Previously coated * Prepare as below N/A Celloted - New N/A N/A Celloted - Previously coated ** Prepare as below N/A Previously coated*mineral surface or fiber cement Poor condition: Remove existing paint completely. Make sure plaster or concrete surface is in good condition. Continue as for new mineral substrate or Fiber Cement substrate. Good condition: Sand down glossy surfaces, ensure surface is clean and dry. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with FLEX FILL (MXRP-2) or POWDER FILL (MXF-2). After drying seal POWDER FILL (MXF-2) with SEALER (MB-30). Previously coated** Cellotex Remove poorly adhering paint and sand down glossy surfaces. Make sure surface is clean and dry. Apply 2 coats CEILING PAINT (EZ-1) with a sheepskin roller. NB: Always use a sealer and / or primer, before applying PVA ALL IN ONE. For sealer and filler application instructions, see relevant data sheets. Remember - a system is only as good as the substrate. For application surfaces, other than above, please contact our sales department. Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water. Ventilation Ensure adequate ventilated application area. Spillages Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact.  ...

Product Code: MB-5 Features: Anti-efflorescent and Water repellant additive for plaster. CEMENT ADDITIVE is a cement additive free of halogens and other aggressive constituents. It is eminently suitable for the modification of building plaster. As a concrete and plaster additive which blocks efflorescence properties and in the production of a modified mortar. As additive in the production of concrete flooring  PROPERTIES DATA UNITS Resin Type Alkaline Stable - Cleaning Solvent Water - Shelf Life 6 Months Unit Sizes and Weights 20Ltr =21,1kg, 5Ltr = 5.5kg, 1Ltr = 1.2kg Ltr = kg Plaster mixture: Add 1Ltr of Cement Additive (MB-5) to 50kg of cement. The B-5 must be added to the water, before addition of sand and cement! NB: For application surfaces, other than above, please contact our sales department. Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water. Ventilation Ensure adequate ventilated application area. Spillages Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact.  ...

Product Code: MDC Features: Water-based, Pure Acrylic Roof Paint, Ready to use, Self-priming, Heat reflective The development of COOLROOF was based on our - over 2 decades successfully performing – PeraRoof. By using latest technologies and high performance raw materials, obvious improvements in a number of aspects have been achieved: No bleeding or washing off during rainfalls Colour retention, as only lightfast pigments are used (no chalking or fading) Further increased cooling effect Corrosion protection – self-priming (not in coastal areas) Improved adhesion and over coating. COOLROOF is a water-based – self priming – pure Acrylic roof paint, based on special ceramic fillers and pigments to reflect UV-light rays and to interrupt the conductive heat transfer to the substrate. However, maximum heat reflection will be achieved by using white or pastel shades COOLROOF. The heat isolating properties of COOLROOF are proportional to the applied dry film thickness.  PROPERTIES DATA UNITS Resin Type Pure Acrylic - Drying Times - Touch Dry 30 minutes Drying Times - Hard Dry 2 hours Over coating Time 6 hours Recommended number of coats 2 to 3 - Coverage 4 to 5 m² / Ltr Surface Apperance Matt, Mineral Look - Cleaning Solvent Water - Shelf Life 6 months Available Colours See Colour Card and White other pastel and deep colours on request - Unit Sizes and Weights 20Ltr =22kg, 5Ltr = 5.6kg, 1Ltr = 1.2kg Ltr = kg SUBSTRATE SEALER / FIRST COATER UNDERCOAT, FIRST COATER Galvanized Iron - New PeraMetal Cleaner N/A (Self Priming) Mineral Substrate - Previously coated * Prepare as below Prepare as below Previously coated* surface in good condition Sand down glossy surfaces. Touch up holes with METAL PRIMER (MCWP-1). Make sure surface is clean and dry. Previously coated* surface in poor (paint peeling and extreme chalking) condition Remove existing paint. New galvanized iron: Apply 2 to 3 coats COOLROOF directly onto degreased and cleaned surface. Previously coated mineral substrate On previously coated, prepared surfaces, 2 coats of COOLROOF should be applied. New fiber cement Make sure fiber cement is free from dust & other contaminations by means of stiff brush – if necessary wash with clean water & let dry properly. Apply one coat COOLROOF thinned with 15% water, leave to dry and apply two coats un-thinned. NB: Do not paint a roof in full sun (hot substrate) or very windy conditions. Make sure that the coating is dry, before it rains. Stir well before and during use. The optimal cooling properties of COOLROOF are only achieved with a white or pastel colour. For application surfaces, other than above, please contact our sales department. Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water. Ventilation Ensure adequate ventilated application area. Spillages Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact.  ...

Product Code: MXRP-1 Features: High Flexibility, Good adhesion, Quick sandable FLEX FILL is a highly flexible compound for use as crack filler for interior and exterior masonry, wood and metal surfaces. PROPERTIES DATA UNITS Resin Type Acrylic - Drying Times - Touch Dry Depends on thickness minutes Drying Times - Hard Dry Depends on thickness hours Over coating Time 2 Depends on thickness hours Recommended number of coats N/A - Coverage N/A m²/Ltr Surface Appearance Smooth - Cleaning Solvent Water - Shelf Life 6 Months month Available Colours White - Unit sizes and weights 5Ltr = 5.5kg, 1Ltr = 1.1kg Ltr = kg Cracks and small holes in plaster Surface must be clean and dry. Remove any crumbling plaster. Apply FLEX FILL into cracks with a skimming blade. Leave to dry and sand smooth. If necessary apply again. NB: FLEX FILL may be used to repair cracks in swimming pools or any other area where it will be covered by water. Tools must be cleaned with water immediately after use. For application surfaces, other than above, please contact our sales department ...

Product Code: MET Features: Natural Cementations look, Non-patchy even finish, Long lasting / permeable, Ultraviolet- and alkali resistance, User friendly MEDIUM TEX is creating a natural cementatious finish on exterior and interior walls. To be applied with a lamb wool roller or block brush, depending on desired pattern.  PROPERTIES DATA UNITS Resin Type Acrylic - Drying Times - Touch Dry 30 minutes Drying Times - Hard Dry 2 hours Over coating Time 4 hours Recommended number of coats 1 Prime Coat and 1 to 2 Topcoats - Coverage 5 m² / Ltr Surface Apperance Fine texture, cementatious matt - Cleaning Solvent Water - Shelf Life 6 months Available Colours See Colour card and white - Unit Sizes and Weights 20 Ltr = 32.9kg, 5 Ltr = 8.3kg, 1 Ltr = 1.7kg Ltr = kg SUBSTRATE SEALER / FIRST COATER UNDERCOAT, FIRST COATER Mineral Substrate - New 1 coat MB-20  N/A Mineral Substrate - Previously coated * Prepare as below N/A Previously coated* surface in good condition Sand down glossy surfaces. Touch up holes and cracks with FLEX FILL (MXRP-2) or POWDER FILL (MXF-2). Seal POWDER FILL (MXF-2) with SEALER (MB-30). Make sure surface is clean and dry. Previously coated* surface in poor condition: Remove existing paint. Apply with 2 coats MEDIUM TEX (MET) with a lamb wool roller and if desired, immediately drag with block brush for pattern. NB: Due to the surface texture of MEDIUM TEX, touch-up areas will appear different in colour, due to texture. It is therefore advisable to paint the surface from joint to joint or corner to corner. For application on surfaces, other than above, please contact our sales department (Tel: (061) 22 7050) or the technical department (Tel: (061) 22 7773). Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water! Ventilation Ensure adequate ventilated application area! Spillages Soak up with sand or soil. Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact. Keep away from open flames. ...

Product Code: MXC-1 Features: Multi-purpose Metal Cleaner METAL CLEANER is a water-based cleaner to remove the wax layer from galvanised iron, prior to coating with METAL PRIMER (MCWP-1) and / or COOLROOF (DC). It may also be used to remove grease or oil from metal. It does not contain Hydrochloric Acid. PROPERTIES DATA UNITS Appearance Blue Liquid - Coverage 6 m²/Ltr Cleaning Solvent Water - Shelf Life 6 Months Recommended number of Applications 1 to 2  - Unit Sizes and Weights 5Ltr = 5.2kg, 1Ltr = 1.2kg Ltr = kg New galvanised iron: Apply on substrate with a brush. Leave for 10 to 15 minutes. Wash with clean water, until all dirt and cleaner is removed. If necessary repeat procedure. Apply Coolroof (MDC) as soon as possible. Old galvanised iron: Replace badly rusted sheets and remove millscale and rust. Proceed as above. NB: The METAL CLEANER has to be washed of thoroughly with clean water. The clean substrate has to be over-coated as soon as possible. For application surfaces, other than above, please contact our sales department. Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water. Ventilation Ensure adequate ventilated application area. Spillages Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact.  ...

Product Code: MB-6 Features: Increases Cement Plaster Flexibility PERA FIX is a cement additive free of halogens and other aggressive constituents. It is eminently suitable for the modification of building plaster. As a concrete and plaster additive (improves elasticity, adhesion and ratio of transverse and compressive strength) and in the production of plastics a modified mortar. As additive in the production of concrete flooring (improves levelling, adhesion and enhances the early and ultimate strength of the floor). PROPERTIES DATA UNITS Resin Type Alkaline Stable - Cleaning Solvent Water - Shelf Life 6 Months Unit Sizes and Weights 20Ltr =24,3kg, 5Ltr = 6.3kg, 1Ltr = 1.3kg Ltr = kg Consolidation of old crumbling cement floors: Clean thoroughly. Saturate floor with PeraFix: Water in a ratio of 1:4. Avoid an excess of PeraFix:Water, as this can lead to the formation of a film, that becomes sticky under the influence of heat and can be peeled off.   Coating of freshly laid cement floors - to strengthen the surface and as protection against dirt: Dilute PeraFix with water in a ratio of 1:4. Apply to floor, as soon as it can be walked upon, by means of spraying, or with a rubber spreader. This measure is particularly important if surfacing is ultimately to be carried out.   Reducing shrinkage and the danger of cracking in floating floors: For this, 1 to 2% PeraFix, calculated on the cement content, is added to the mortar. If poor quality sand is used this amount should be increased to 10%. The PeraFix is best added to the make-up water or, if a mechanical mixer is used, directly to the mixer. It is advisable to apply a coating, as described in "2", to the floating floor.   Levelling compound for mastic asphalt: For this purpose PeraFix is mixed with fine, washed sand or with river sand until a mixture, which can easily be trowelled, is produced. The ratio of PeraFix: Sand is about 1:3 by weight.   Levelling compound for concrete: Portland Cement (type PZ 275) is mixed with fine river sand (max. particle size: 0,5 - 1 mm), in a ratio of 1:1,5 to 1:2 per weight. The coarser the grains, the more sand can be used. The mixture is moistened with PeraFix:Water in a ratio of 1:1. This mixture is applied to the cleaned substrate that has been saturated with a mixture of Perafix:Water in a ratio 1:4. The applied levelling compound must be kept moist for 1 to 2 days. The addition of fused alumina cement, to the Portland cement, accelerates hardening. We recommend the application of a mixture as described in "2".   Repair of damaged or uneven concrete flooring: Unevenness in cement flooring and in concrete is, after thorough cleaning of the substrate, saturated with a mixture of PeraFix:Water in a ratio of 1:4. Before this coating has dried, a mortar, consisting of 3 parts by volume of sand (particle size 0 to 3 mm) and 1 part by volume ordinary Portland cement, compounded with a mixture of PeraFix:Water in a ratio of 1:4, is used to make good the damage. More severe defects can be prefilled with this mortar and a levelling compound, as described under 5, applied. This mortar can also be used for the preparation of actual flooring.   Increasing adhesion and elasticity, as well as reducing the tendency to crack, of terrazzo or single layer hard concrete flooring: The substrate is pre-treated with a mixture of Perafix:Water in a ratio of 1:4. The mortar is prepared with the same mixture, instead of water. In the case of double-layer, hard concrete flooring, these recommendations apply only to the lower layer.   Base for bonding old and new concrete: The old, thoroughly cleaned floor, is primed with a mixture of PeraFix:Water in a ratio of 1:4. A mixture, consisting of 1 to 2 parts by volume of sand, particle size 0 to 3 mm and, 1 part by volume of cement, mixed with PeraFix:Water in a ratio of 1:4, is brushed into the wet priming coat. Ordinary cement mortar (or concrete) is cast onto this base, while it is still wet.   Towelling compounds based on cement or casein for substrates: These can be made to adhere more easily to the substrate if a mixture of PeraFix:Water, in a ratio of 1:4 to 1:8, is used instead of water for preparing the compound.   Smoothing, waterproofing compound for spraying, brushing or towelling: A mixture of: 1 part by volume PeraFix 1 part by volume Ordinary white or grey Portland cement 2 parts by volume Water is thoroughly stirred and applied to the surface by means of a spray gun (2,5mm jet, 2.5 atg.), a brush or a smoothing trowel. By further dilution with water, a thinner coat can be applied. This mixture can also be used as a decor plaster, but the mixture may have to be adjusted by up to 1 part by volume clean fine sand (0 to 1mm). The cured coating may then be coated with any conventional builder’s paint.   Improved adhesion of renderings: The bond strength of wall and ceiling renderings can be improved, and their elasticity increased, especially if the surfaces are smooth, by the addition of 5% PeraFix, calculated on the make-up water   Increasing the tensile strength of synthetic/natural anhydrite flooring or plaster moulds: The addition of 5% PeraFix, calculated on the binder increases the bending tensile strength of synthetic anhydrite flooring by approximately 50% (measured on 4 X 4 X 16 cm prisms after thorough drying). The same applies to natural anhydrite. Plaster moulds (e.g. models) can be made practically unbreakable and highly abrasion resistant by a correspondingly high addition of PeraFix, even if the structural components are thin. The desired amount must be determined by preliminary trials, depending on the stress and type of plaster used.   Grouting for all types of wall and floor tiles: A dry mix consisting of: White cement 300 p.b.w. Pera marble dust 600 p.b.w. Rutile Titanium Dioxide 100 p.b.w. is made into a paste with a mixture of PeraFix:Water in a ratio of 1:9. The Titanium Dioxide may be replaced by any inorganic light fast pigment, or mixtures thereof, for coloured grouting. Care must be taken, that these pigments are compatible with cement. NB: Remember - trials should be carried out before application, to familiarise yourself in the use of PeraFix, as well as determining the optimum quantities to be used. PeraFix is not a "super-plasticiser" (for use in high-density concrete), although it has plasticising properties and a reduction in make-up water is usually possible. PeraFix is active in the mortar (better workability, flow, plasticising action, colour development, etc), as well as in the cured concrete (higher transverse and compressive strength, improved elasticity and adhesion, as well as better colour development and colour retention in pigmented systems). PeraFix "cures" by the loss of water, therefore we recommend that PeraFix modified concrete be left to dry after hardening. PeraFix is not recommended for use underwater. For application surfaces, other than above, please contact our sales department. Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water. Ventilation Ensure adequate ventilated application area. Spillages Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact.  ...

Product Code: MRL Features: Superior quality smooth plaster, Long Lasting, On request, available in preferred colours PLAST FINE is a superior quality, smooth plaster for use on interior or exterior surfaces. PROPERTIES DATA UNITS Resin Type Acrylic polymer - Drying Times - Touch Dry 2 hours Drying Times - Hard Dry 24 hours Recommended number of coats 1 - Coverage (1mm) 1.6 to 2 Kg / m² Surface Apperance Slight Sheen, textured - Cleaning Solvent Water - Shelf Life 6 months Available Colours Only on request* - Unit Sizes and Weights 20Ltr =32kg, 5Ltr =8,2kg Ltr = kg *Minimum order is 160kg or 5 x 20Ltr (32kg) New plastered walls and brickwork - Ensure surface is completely dry. Seal surfaces with SEALER (MB-30). Then proceed as follows: After two hours drying time, apply the PLAST FINE (MRL) with a stainless steel trowel and smooth down to the thickness of the largest pebbles (+/- 1mm).Level the plaster to an even and smooth surface with a clean stainless steel trowel (Do not use plastic or wooden trowels). Make sure that the trowel remains clean at all times.   Previously painted surfaces: Remove all dust, dirt, grease and loose or flaking paint. Glossy paints must be sanded to a matt finish (it is not recommended to apply PLAST FINE (MRL) over Enamel paints). Make good any holes and cracks with FLEX FILL (code MXRP) and continue as in (a).   Lime washed surfaces: Remove limewash with a steel brush. Seal surface with 2 (two) coats of solvent-based bonding liquid, leaving a drying time of at least 4 hours in-between coats. After 24 hours drying time continue as in (a).   Surfaces with microbiological problems (fungal or algae growth): Liberally apply an approved detergent and leave for 48 hours. Remove all loose matter and fungal or algae growth with a wire brush. Apply 1 coat anti-fungal SEALER (on request only), followed by anti-fungal PLAST FINE. Where a primer coat is used, this too should be anti-fungicidal. Microbiological problems are usually caused by faulty construction or design - find and remove the cause of the problem whenever possible.  Never apply PLAST FINE in direct sunlight. Use a canvas or plastic sheet to shade areas where work is in progress. Whenever possible, apply on side of structure facing away from sun.   On very large areas apply PLAST FINE in panels (or fields). Allowance should be made for these panels during the design stage of a project. These panels would ideally encompass no more than the area that can be plastered by a single applicator in a shift. Wherever necessary, care must be taken that these panels are easily accessible from the scaffolding.   Where it is possible apply only one batch to a continuous panel or wall. Where this is impossible, ensure that the colour of all batches used, matches.   A single panel or wall should never be left uncompleted.   If more than one person is doing the application, care must be taken that the resultant pattern of any one person matches that of all the others. When choosing persons to apply the plaster, take note that plasterers are better suited than painters. NB: Remember - a system is only as good as the substrate. Replaster walls where the old plaster is crumbling or detached. Never use inferior sealers or primers. One coat CLEAR COAT (MB-9) is recommended for interior application over these systems in high traffic areas, to improve gloss and cleanability and to decrease dirt retention. For application surfaces, other than above, please contact our sales department or the technical department. Gloves X Mask - Goggles X     Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical advice! Skin Contact Immediately wash skin with soap and water!     Ventilation Ensure adequate ventilated application area! Spillages Soak up with sand or soil. Prevent run off into drains or water ways.     Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact. Keep away from open flames. ...